The Melodie loudspeaker is a self-powered, three-way design featuring drivers designed and manufactured at Meyer Sound’s Berkeley, California, factory.
The low/low-mid section features two high-power,neodymium-magnet, 8-inch cone drivers with 1.5-inch voice coils, created to meet the power requirements of the system. The drivers are a proprietary design employing neodymium magnets for higher efficiency and power handling with reduced weight.
he lowest frequency range is reproduced by these high-power drivers working in tandem, each powered by a dedicated amplifier channel. To assure the smoothest response in the critical midrange and crossover region, M’elodie incorporates a complex active crossover design.
For low frequencies, both drivers work together, but in the low-mid frequencies only one of the two 8-inch drivers is active. This technique eliminates interference between the drivers that would otherwise occur at shorter wavelengths, while at the same time maintaining optimal polar and frequency response characteristics at the crossover frequency.
The high-frequency section uses a 1.2-inch exit, 3-inch diaphragm compression driver with a neodymium magnet, powered by a dedicated amplifier channel. The output of the driver is coupled to a 100-degree (horizontal coverage) constant-directivity horn through a custom REMmanifold.
The REM is a patented coupling device that introduces driver output to the horn throat across a very short path,effectively controlling the dispersion characteristics, but with dramatically reduced distortion in comparison to other techniques.
Compact High-Power Subwoofer
The 600-HP is a self-powered, high-output subwoofer that may be used in both flown and ground-stacked configurations. It is designed to rig directly with MICA compact, high-power curvilinear array loudspeakers when fitted with the optional QuickFly MRF-600 rigging frame. The versatility of the 600-HP also allows it to be used with a variety of other Meyer Sound self-powered loudspeakers — such as CQ-1, CQ-2, UPA-1P, UPA-2P and UPJ-1P — in fixed and touring applications.
The system features two specially designed high-power 15-inch cone drivers, engineered to provide optimal performance in subwoofer applications. The high-excursion, back-vented drivers have 4-inch voice coils, and each is rated to handle 1200 watts (AES*).
The two cone drivers are housed in a rectangular, optimally tuned and vented enclosure that is the same width as MICA, and a few inches higher and deeper. The enclosure geometry makes vertical ground-stacking easy and convenient. All versions include plastic skids on the bottom of the unit to prevent damage to the enclosure or the unit below the skids align with slots on the cabinet’s top to ensure secure stacking. Operating frequency range is from 36 Hz to 150 Hz, with a peak SPL at one meter of 138 dB.
Each cone driver is driven by a channel of the integral two-channel class AB/H amplifier with complementary MOSFET output stages. Total output power is 2250 watts (4500 watts peak), providing the system with sufficient headroom to accommodate the most extreme sound reinforcement demands with ease. The circuitry includes TruPower limiting to extend the life of the drivers and hold long-term power compression to less than 1 dB. The amplifier, control electronics, and power supply are integrated into a single, field-replaceable module that is mounted into the rear of the enclosure.
The optional MRF-600 rigging frame uses captive, rigid GuideALinks contained within recessed guides in the lower front and rear corners of the enclosure. A slot and convenient pinned handle allow the link to be moved and pinned for arraying or storage. The versatility of angles achieved by using combinations of front and back positions allows a MICA array suspended under 600-HP subwoofers to be uptilted for balcony coverage up to 15 degrees, or downtilted to 6 degrees with respect to the 600-HP. The 600-HP can make use of the optional MG-MICA rigging grid to accommodate a variety of flown and stacked configurations.
The durable enclosure is constructed of premium birch plywood coated with a black, tex- tured hard-shell finish, with a powder-coated, hex-stamped steel grille lined with acoustical black mesh to protect the drivers. The exterior dimensions of the 600-HP are suitable for both European and U.S. trucks, and it can securely travel in stacks using the MCF-MICA caster frame, or MDB-600 dolly board when not fitted with rigging frames.
Options for the 600-HP include weather pro- tection and custom color finishes for fixed installations and other applications requiring specific cosmetics. The RMS remote monitor- ing system — standard with the rigging version and optional with other configurations — allows comprehensive monitoring of system parameters on a Windows-based network.
- Efficient, high-power and high-excursion cone drivers
- Extremely low distortion for low-frequency clarity
- Very high peak power yields excellent transient reproduction
- Low-frequency complement to MICA and other Meyer Sound self-powered loudspeakers
When fitted with MRF-600 rigging frames:
- Stackable, and flyable by itself or with MICA full-range loudspeakers
- Transportable in stacks using optional MCF-MICA caster frame
- Medium to large theatres and clubs
- Houses of worship
- Portable and installed A/V systems